VAG COM 20.4.1 čeština ATMEGA162 Interface is latest full active vag diagnostic cable centre. VCDS 19.6.1 SVO Bootloader hex can usb interface with ATMEGA162 + FT232RL + L9637D + 16V8B. VCDS 18.9 Czech full active cable support For VW Audi Seat Skoda till 2017 model.
Atmel Chip čeština vag com 18.9.0 vcds 19.6.1 SVO 20.4.1 full active Vag hex Cz can crack cable
VCDS Multilanguage Vagcom 18.2 Choose:
Option 1: vcds 18.9 with Czech
Option 2: vag com 19.6.1 SVO
Option 3: vag com 20.4.1 SVO or 20.12
VAG COM VCDS 18.9.0 Features:
Language: Czech
Software Version: VCDS 18.9/ 19.6.1/20.4.1
Firmware Version: 1.96
Supported Vehicle List: For AUDI VW SEAT SKODA
Chip Edition: ATMEGA162 + FT232RL + L9637D + 16V8B
System requirement: Windows XP, Vista, 7, 8 and 10(32-bit and 64-bit)
(It does not support Windows 95, 98, ME, and NT4 operating system)
Note: VCDS 18.9 and 19.6.1 Czech is not NEC project, ATMEGA162 + FT232RL + L9637D chips with Bootloader support flash to any version and languages by your dumps!!
VCDS 18.2 New added functions compare VAGCOM 17.1.3:
-Support for MLB2 platform cars (HEX-NET interface recommended)
-Support for 2016 and early model cars
-Greatly expanded the amount of DTC Freeze-Frame data dsiplayed
-Improvements in Advanced Measuring Value Selection Window
-Display of factory identifiers instead of arbitrary location numbers
-Support for Six-Digit security access codes
-HEX-NET Turbo and other speed optimizations
-Optimized low-level timing routines and CPU core affinity
-Major firmware enhancements for HEX+CAN and Micro-CAN interfaces
-Improved UDS mapping speed and reliability when subchannels are present; progress indicators.
-Fixes SRI reset in newer Crafter instruments.
-New ASAM data and Label Files
-Support vehicle list: For AUDI VW SEAT SKODA
DIY VAG COM 20.13.0 HEX V2 Interface MQB HEX V2 unlimited VIN Diagnostic Cable for VW Audi Seat Skoda
Vagcom 18.9 New Features:
Auto Scan 1001.01
1. Control module unit information
2. Read fault codes 004.01
3. Output test 005
Selective output test 005
4. Basic settings 006
5. Clear DTCs 004.10
6. Close control module 022
7. Pairs of coding control module (brush hidden) 007 (service 1A)
008 (Service 22) From the station control module 007 coding (service 1A)
008 (Service 22) Read measured value block 08 010.02 (KWP1281)
8. Advanced measurement reading
9. channel read 010.01
10. matching 012 014 (long)
11. Log (Known under KWP-2000 * Coding II) 015.01
12. View readiness 020.01 Guided ready state settings
13. security access 015.02
14. All supported DTCs
15. Common OBD-II function
16. Fault environmental data
17. Dual K-Line Support 7-PIN code 020.07
18. Upgrade to the latest fault code library
19. Direct CAN line diagnosis (Need to support diagnostic cables CAN line diagnosis)
20. Modes of transport 1001.03 (on)
1001.04 (off) (Need to support diagnostic cables CAN line diagnosis)
21. Advanced measurement block
22. Support for dual engine control module
Compared to the previous version, the VAG 17.8 main changes is BUG fixes and improvements.
Vag com 18.2 Basic functions
00 Auto Scan
01 control module unit information
02 read fault codes
03 Output Test
Selective output test (only for KWP-2000 *)
04 Basic settings
05 clear DTCs
06 Close Control Module
07 pairs of coding control module
Slave control module for coding (only for KWP-2000 *)
Read measured value block 08
09-channel read (applies only to KWP-1281 *)
10 matching
11 Log (known under KWP-2000 * Coding II)
15 View Ready
16 security access (only for KWP-2000 *)
18 All supported fault codes (only for KWP-2000 *)
33 Common OBD-II function
VAG 18.2 Install Guide:
Downloaded VCDS software installation file, turn off internet, follow the steps to install the software correctly VCDS,You must install VCDS software on your computer's hard drive!( When installing software, please not plug cable with your PC!!)
Please dont run directly from other media VCDS software, the software may not run correctly
You can use a CD or USB flash drive to copy files to install VCDS on your computer hard drive you want to install, and then install it.
The appropriate diagnostic cable to connect the computer to the vehicle and turn the ignition switch of the vehicle, but it is not necessary to start the engine.
Click the [System Configuration], and then select the correct communications port
Click [Test] to confirm VCDS program can use the correct communications port, find diagnostic cables
Then click [Save]
You can now use all the features of the program VCDS. Ensure VCDS software can reliably access all the control modules that you have a vehicle to view the fault code. See the VCDS diagnostic system for vehicle applications list
VAG COM 18.9 Packing List:
1 x Vagcom 18.9 diagnostic cable
1 x CD with VCDS 18.9 or 19.6.1 software
OBD2cartool After-Sale Service:
Technical Support: Free
Whatsapp:+86-13537734676
Live Support: Chat with us online
Email: obd2cartool@hotmail.com
Skype: great2obd
If you have any problem, please do not hesitate to contact us.
Wholesaler Discount: If you are wholesaler or reseller, pls send email to obd2cartool@hotmail.com, we will give you best discount for long-term cooperate.
Payment Terms: We accept payment by paypal, western union, money gram and bank transfer.
Shipment Note:
1. All our free shipping items can track it online after delivery, you don't worry about your order status.
2. Express Delivery we will send to you with DHL,EMS,UPS,FEDEX,TNT..., please give us a valid delivery phone number, and also a full and accurate shipping address.
How to make order on OBD2cartool.com?
Notice: After you place order, pls reply confirm email send by obd2cartool@hotmail.com asap for us to arrange ship for you, thanks